Marijuana.com

Vish · 09-11-2008, 09:23 PM

Well I'm currently making my own Bong. I have everything set but I need a bowl. I found something that will work, but it is porcelain. Does anyone know if it's bad to smoke from a porcelain bowl? Thanks.

Also, what should I use to fasten it on? Tape? Glue? I have no idea, but I'm guessing it won't burn the tape/glue.

**sterbo** · 09-11-2008, 10:15 PM

No problem.
Porcelain is typically fired at a couple thousand +degrees F. The base material (typically high % of clay) is perfect for such use.

Maybe you can send us a picture once your bong is ready for prime time...

Vish · 09-11-2008, 11:46 PM

It's not so great. I hope to god I burnt out all the Superglue. I ran a torch on the inside of the bowl for a bit. A lot of smoke came out. Just finished it. It's made of a pepsi max bottle, a metal tube, and a porcelain bowl put on with p-tex. Should (?) work.

I'll probably run more fire through it tonight. Not sure. I hope that the glue is out..

SimpleGreen · 09-13-2008, 12:24 AM

Looks like it would be awkward to light.

09-13-2008, 04:34 AM

Dude, all I can say is dont burn an eyebrow on that thing.

The bowl is right up close to your face...

**dirtbomb** · 09-13-2008, 05:16 AM

Caulk, like they use to seal bathroom fixtures, is much safer than using super glue.
Raise that downpipe a little and it should make a few parties a lot more fun.

GREENFOODGAMES · 09-15-2008, 06:30 PM

Ugh that bowl is a little close to the mouthpiece for my liking, I also dont see any type of a carb either. And everybody knows you use a Dr. Pepper Bottle my god - J/K, I had to do that. I would seal that hole you have change the angle on that bowl piece so it comes in lower and out further to save you eyebrows, and make a carb and inch or two above you're water line and it should hit fine. Good luck with it

09-11-2008, 09:23 PM	#1
Vish New Member Join Date: Jul 2008 Posts: 3 Grams: 377.50 Groans: 0 Groaned at 0 Times in 0 Posts Thanks: 0 Thanked 1 Time in 1 Post Stock Portfolio Total Value: 0.000 Gain/Loss: 0.000%	Porcelain Bowls Well I'm currently making my own Bong. I have everything set but I need a bowl. I found something that will work, but it is porcelain. Does anyone know if it's bad to smoke from a porcelain bowl? Thanks. Also, what should I use to fasten it on? Tape? Glue? I have no idea, but I'm guessing it won't burn the tape/glue.

09-11-2008, 10:15 PM	#2
sterbo sailor dog... Join Date: Feb 2007 Posts: 5,728 Grams: 19,139.62 Groans: 28 Groaned at 20 Times in 15 Posts Thanks: 2,753 Thanked 3,316 Times in 1,444 Posts Stock Portfolio Total Value: 0.000 Gain/Loss: -1.000%	No problem. Porcelain is typically fired at a couple thousand +degrees F. The base material (typically high % of clay) is perfect for such use. Maybe you can send us a picture once your bong is ready for prime time... __________________

09-15-2008, 06:30 PM	#7
GREENFOODGAMES Member Join Date: Aug 2008 Posts: 1,171 Grams: 6,243.80 Groans: 5 Groaned at 3 Times in 3 Posts Thanks: 210 Thanked 264 Times in 213 Posts Stock Portfolio Total Value: 0.000 Gain/Loss: 0.000%	Ugh that bowl is a little close to the mouthpiece for my liking, I also dont see any type of a carb either. And everybody knows you use a Dr. Pepper Bottle my god - J/K, I had to do that. I would seal that hole you have change the angle on that bowl piece so it comes in lower and out further to save you eyebrows, and make a carb and inch or two above you're water line and it should hit fine. Good luck with it __________________ "Prohibition goes beyond the bounds of reason in that it attempts to control a man's appetite by legislation and makes crimes out of things that are not crimes. A prohibition law strikes a blow at the very principles upon which our government was founded." Lincoln

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

New To Site?	Need Help?
Register to Participate View Forum Leaders Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read

Remove Advertisements Marijuana.com Sponsor
Marijuana.com Advertisement	<a rel='nofollow' href='http://adserver.marijuana.com/www/delivery/ck.php?n=a78e9dba&cb=INSERT_RANDOM_NUMBER_HERE' target='_blank'><img src='http://adserver.marijuana.com/www/delivery/avw.php?zoneid=6&cb=INSERT_RANDOM_NUMBER_HERE&n=a78e9dba' border='0' alt='' /></a>

09-11-2008, 11:46 PM	#3
Vish New Member Join Date: Jul 2008 Posts: 3 Grams: 377.50 Groans: 0 Groaned at 0 Times in 0 Posts Thanks: 0 Thanked 1 Time in 1 Post Stock Portfolio Total Value: 0.000 Gain/Loss: 0.000%	It's not so great. I hope to god I burnt out all the Superglue. I ran a torch on the inside of the bowl for a bit. A lot of smoke came out. Just finished it. It's made of a pepsi max bottle, a metal tube, and a porcelain bowl put on with p-tex. Should (?) work. I'll probably run more fire through it tonight. Not sure. I hope that the glue is out..

09-13-2008, 12:24 AM	#4
SimpleGreen Jr. Member Join Date: Sep 2007 Posts: 225 Grams: 2,400.90 Groans: 1 Groaned at 1 Time in 1 Post Thanks: 50 Thanked 110 Times in 65 Posts Stock Portfolio Total Value: 0.000 Gain/Loss: 0.000%	Looks like it would be awkward to light.

09-13-2008, 04:34 AM	#5
The Blazemaster Posts: n/a Grams: 0 [Check] Stock Portfolio Total Value: Gain/Loss: %	Dude, all I can say is dont burn an eyebrow on that thing. The bowl is right up close to your face...

09-13-2008, 05:16 AM	#6
dirtbomb Anime Villain Join Date: Sep 2008 Posts: 766 Grams: 4,334.60 Groans: 0 Groaned at 2 Times in 2 Posts Thanks: 229 Thanked 241 Times in 167 Posts Stock Portfolio Total Value: 0.000 Gain/Loss: 0.000%	Caulk, like they use to seal bathroom fixtures, is much safer than using super glue. Raise that downpipe a little and it should make a few parties a lot more fun.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Marijuana.com

Hot Products: