| |||||||
| Register | FAQ | Gaming | VB Image Host | Search | Today's Posts | Mark Forums Read |
| | LinkBack | Thread Tools | Display Modes |
| | #1 |
| New Member Join Date: Dec 2007
Posts: 35
Grams: 915.00 Groans: 1
Groaned at 0 Times in 0 Posts
Thanks: 3
Thanked 8 Times in 8 Posts
| I just recently bought a new acrylic bong, and while it hits like a champ, I've noticed that it begins leaking after a long session, or even just during regular use. I took the base off, and found that it was the bottom cap that seems to be causing the problem. It's not very air tight, and there are no sealants around it. I was wondering if anyone had any suggestions as to a permanent fix. I thought about melting a candle around the base to seal it, but I wasn't quite sure if that would really do the job. It was only a $30 bong, but I'm a poor high school student, so I just don't have the funds for a nicer glass one. Any help is greatly appreciated. Thanks. ![]() |
| | |
| Marijuana.com Sponsor | |
Advertisement | |
| | #2 |
| New Member Join Date: Feb 2008
Posts: 8
Grams: 548.35 Groans: 0
Groaned at 0 Times in 0 Posts
Thanks: 0
Thanked 0 Times in 0 Posts
| Hmm, do you have any caulking around your house? You know the stuff around the bathroom sink to keep it watertight? If so a small ammount around the cap might do it, just make sure its 100% dry before you try using it again. |
| | |
| | #3 |
| Subscriber ![]() ![]() Join Date: May 2007
Posts: 2,939
Grams: 25,545.80 Groans: 20
Groaned at 26 Times in 20 Posts
Thanks: 715
Thanked 1,175 Times in 772 Posts
| Plumbing Repair Guide: How To Use Teflon Tape - ACME HOW TO.com Plumbers tape. Follow those instructions (substituting "pipe" for "bong") and you'll be fine.
__________________ "No references to the need to fight terror can be an argument for restricting human rights." - Vladimir Putin "It has been said that democracy is the worst form of government except all the others that have been tried." - Sir Winston Churchill "A casual stroll through the lunatic asylum shows that faith does not prove anything." - Friedrich Nietzsche "Fashion is a form of ugliness so intolerable that we have to alter it every six months." - Oscar Wilde "I count him braver who overcomes his desires than him who overcomes his enemies." - Aristotle |
| | |
| The Following 2 Users Say Thank You to Trocisp For This Useful Post: | JaggedJesus (02-18-2008), SpiralArchitect (02-18-2008) |
| | #4 |
| Alaskan Thunderfuck ![]() ![]() ![]() ![]() ![]() Join Date: Dec 2006
Posts: 5,009
Grams: 33,235.87 Groans: 76
Groaned at 21 Times in 18 Posts
Thanks: 3,235
Thanked 2,012 Times in 1,160 Posts
| I'd go with what idea Trocisp provided. I would avoid melting the candle, especially if you were planning on doing it inside the bong. The heat would warp the bong and give off nasty fumes. If neither of those methods work, as a last ditch effort I would seal the base of the bong with some sort of adhesive. However having a removable base to a bong is rather handy when it comes to clean-up time. |
| | |
| | #5 |
| New Member Join Date: Dec 2007
Posts: 35
Grams: 915.00 Groans: 1
Groaned at 0 Times in 0 Posts
Thanks: 3
Thanked 8 Times in 8 Posts
| Thanks a lot for the help, guys! I seem to remember seeing some Teflon tape downstairs. I hadn't thought to use it on a bong, though. |
| | |
| Marijuana.com Sponsor | |
Advertisement | |