Marijuana.com

Mighty Boot · 08-14-2003, 06:29 AM

I wish it were that easy, but safe at the same time; Aluminum foil fumes are BAD. BAD BAD BAD.

BloodNOil · 08-14-2003, 06:41 AM

Go to a hardware store and get some brass tube... note the
outside diameter, and find some brass "compression fittings" for
said tube... Use your imagination here...

Use either super glue, thread locker, or silicone RTV/sealant for
the adhesive...

Actually, i havent tested them all but thread locker is all right as
long as the bowl doesnt get too hot (300 degrees or hotter...
you'll burn yourself on it or your bong water will boil before it gets
that hot... just dont use a torch lighter)

and DO NOT use aluminum foil for the gauze/screen... thats
almost worse than using it for the bowl... if you HAVE to make
your own screen, remember that you're in a hardware store and
make it with stainless steel or brass (stainless is better)

edit: If you have a propane torch, be sure to "cook" alllll of the
grease off of everything... If you don't have a propane torch,
remember that you are in a hardware store.

edit: After maybe 10 sec of continuous bic lighter flame, the
thread locker will break down and emit black smoke... Since
thread locker is CYANOacrylic (cyan as in cyanide), this black
smoke cann't be good for you.

Mighty Boot · 08-14-2003, 07:39 AM

Uhhh.. Cyanacrylic as in Cyanide? I'd stay well away from that. I mean you never can be TOO sure you've burned it all off.

EDIT: oh.. yes as in cyanide.. duh.

zoltron · 08-14-2003, 08:00 AM

grab the thimble out of yo' mama's sewing kit...turn upside-down
and drive a little nail in the top a few times for holes, and there
you have it.

Fluke_24 · 08-14-2003, 08:58 PM

You can use the mouthpiece of an instrument or a the top of a salt shaker.

08-14-2003, 06:29 AM	#11
Mighty Boot Jr. Member Join Date: Jul 2003 Posts: 209 Grams: 711.85 Groans: 0 Groaned at 0 Times in 0 Posts Thanks: 0 Thanked 0 Times in 0 Posts Stock Portfolio Total Value: 0.000 Gain/Loss: 0.000%	I wish it were that easy, but safe at the same time; Aluminum foil fumes are BAD. BAD BAD BAD. __________________ Bud Boys for life!

08-14-2003, 06:41 AM	#12
BloodNOil Member Join Date: May 2003 Posts: 1,314 Grams: 1,760.65 Groans: 0 Groaned at 0 Times in 0 Posts Thanks: 0 Thanked 0 Times in 0 Posts Stock Portfolio Total Value: 0.000 Gain/Loss: 0.000%	Go to a hardware store and get some brass tube... note the outside diameter, and find some brass "compression fittings" for said tube... Use your imagination here... Use either super glue, thread locker, or silicone RTV/sealant for the adhesive... Actually, i havent tested them all but thread locker is all right as long as the bowl doesnt get too hot (300 degrees or hotter... you'll burn yourself on it or your bong water will boil before it gets that hot... just dont use a torch lighter) and DO NOT use aluminum foil for the gauze/screen... thats almost worse than using it for the bowl... if you HAVE to make your own screen, remember that you're in a hardware store and make it with stainless steel or brass (stainless is better) edit: If you have a propane torch, be sure to "cook" alllll of the grease off of everything... If you don't have a propane torch, remember that you are in a hardware store. edit: After maybe 10 sec of continuous bic lighter flame, the thread locker will break down and emit black smoke... Since thread locker is CYANOacrylic (cyan as in cyanide), this black smoke cann't be good for you. __________________ It's like a koala bear crapped a rainbow in my brain!!

08-14-2003, 08:00 AM	#14
zoltron Banned Join Date: Jun 2003 Posts: 2,344 Grams: 32.75 Groans: 0 Groaned at 0 Times in 0 Posts Thanks: 0 Thanked 4 Times in 2 Posts Stock Portfolio Total Value: 0.000 Gain/Loss: 0.000%	sew what? grab the thimble out of yo' mama's sewing kit...turn upside-down and drive a little nail in the top a few times for holes, and there you have it.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

New To Site?	Need Help?
Register to Participate View Forum Leaders Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read

Remove Advertisements Marijuana.com Sponsor
Marijuana.com Advertisement	<a rel='nofollow' href='http://adserver.marijuana.com/www/delivery/ck.php?n=a78e9dba&cb=INSERT_RANDOM_NUMBER_HERE' target='_blank'><img src='http://adserver.marijuana.com/www/delivery/avw.php?zoneid=6&cb=INSERT_RANDOM_NUMBER_HERE&n=a78e9dba' border='0' alt='' /></a>

08-14-2003, 07:39 AM	#13
Mighty Boot Jr. Member Join Date: Jul 2003 Posts: 209 Grams: 711.85 Groans: 0 Groaned at 0 Times in 0 Posts Thanks: 0 Thanked 0 Times in 0 Posts Stock Portfolio Total Value: 0.000 Gain/Loss: 0.000%	Uhhh.. Cyanacrylic as in Cyanide? I'd stay well away from that. I mean you never can be TOO sure you've burned it all off. EDIT: oh.. yes as in cyanide.. duh.

08-14-2003, 08:58 PM	#15
Fluke_24 New Member Join Date: Jun 2003 Posts: 48 Grams: 569.05 Groans: 0 Groaned at 0 Times in 0 Posts Thanks: 0 Thanked 0 Times in 0 Posts Stock Portfolio Total Value: 0.000 Gain/Loss: 0.000%	You can use the mouthpiece of an instrument or a the top of a salt shaker.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Marijuana.com

Hot Products: